Home Improvement

How to Clean Your Vacuum Cleaner in 6 Steps

It is very important to frequently clean your vacuum cleaner now and then. It is only fair that the machine that removes debris, dust and other dirt from the carpet and rugs should also receive adequate attention. If you want to continue to maintain the cleanliness of your rugs and carpets, then you should know how to properly clean the tool that cleans. This will help to prevent dust from being blown back into your room.

One thing about vacuuming is that the better care you give to the vacuum cleaner, the more efficient it will also perform. The failure to take proper care of your vacuum cleaner will cause it to inadequately clean the dirt and dust from the floor or rug. In addition, it may even result in the blowing of some debris back into the room. In essence, we have written this guide to help you understand how you can properly clean your vacuum cleaner. Follow the steps highlighted below, and you’re good to go!

  1. Begin with the canister/bag 

    The first thing to do, depending on the type of vacuum cleaner you use, is to take out the bag or canister, pour out the dust and debris that have accumulated in it, and then clean the bag. In the case of canisters, all you have to do is just empty the dirt in a trash can and then go ahead to wash the container. Be sure to use soap and warm water to clean the container, and then allow it to dry completely before fixing it back.It is advisable that you make it a regular practice to dump the contents of the bag or replace it before it is completely full. Ideally, the recommended timing for addressing the bag is about ⅔ of the way.

  2. Cleaning the vacuum filter 

    The next thing to do is to clean the vacuum filter with water. This step is very important, particularly for individuals who complain of an unpleasant smell in the room after vacuuming. Proper cleaning of the filter is enough to resolve this problem. Importantly, make sure that the filter is completely dry before you return it back into the vacuum cleaner.

  3. Check for blockages in the vacuum cleaner 

    To inspect the vacuum cleaner for blockages, remove the vacuum hose and properly examine the inside after straightening it. If you notice any blockages, get a wire hanger and straighten it. If you don’t find a wire hanger, grab any other straight object and poke the inside of the hose to remove any dirt that may be blocking it.To achieve full vacuum efficiency, it is necessary to free your hose from every debris that might be blocking it. However, it is also essential that you are cautious so as not to puncture the hose. Such damage may lead to expensive repairs. Another thing you can do regarding the hose is to wrap a couple of wet wipes or dryer sheets over the object you are using to clean it. Since debris can easily settle in a lot of places inside the hose, it is essential to dust the inside thoroughly. In all, be careful not to cause any costly damage to the vacuum components.

  4. Sanitising the vacuum hose 

    Do you want to be more thorough in the cleaning of your vacuum hose? Then you should add white vinegar solution. This is a brilliant idea considering the fact that the vacuum hose literally encounters all of the dust and dirt that are sucked in by the vacuum cleaner. Thus, it comes in contact with several germs, and it must be well cleaned every now and then. Vinegar is an ideal solution for cleaning this region. All you have to do is dampen a paper towel with vinegar and attach it to a wire hanger. Stick it into the vacuum hose and clean it as well as you can. Allow the hose to dry completely before you reassemble it and use it again.

  5. Examine the condition of the beater brush 

    To inspect the condition of the beater brush, place the vacuum on one side and use a pair of scissors to trim out any hairs lurking within. Properly inspect the component for any other dirt that may be stuck in it. You should also take the opportunity to inspect if the belt of the wire brush has any cracks. If the need be, you may have to replace it.

  6. Use a damp cloth to wipe the external part of the vacuum cleaner 

    It is a best practice to clean the external parts of your vacuum cleaner with a damp towel after you have finished cleaning all of the internal components.Conclusion

We guarantee that your vacuum cleaner will work better and last longer if you follow all of these 6 guidelines. if you need any help, contact professional carpet cleaner to assist you in all of your cleaning needs. What’s more is that our cleaning services cover both domestic and commercial facilities.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *

Back to top button